12. Environment variables

This is the list of environment variables that affect the behavior of Fast DDS:

12.1. FASTRTPS_DEFAULT_PROFILES_FILE

Defines the location of the default profile configuration XML file. If this variable is set and its value corresponds with an existing file, Fast DDS will load its profiles. For more information about XML profiles, please refer to XML profiles.

Linux

 
export FASTRTPS_DEFAULT_PROFILES_FILE=/home/user/profiles.xml

Windows

 
set FASTRTPS_DEFAULT_PROFILES_FILE=C:\profiles.xml

12.2. SKIP_DEFAULT_XML

Skips looking for a default profile configuration XML file. If this variable is set to 1, Fast DDS will load the configuration parameters directly from the classes’ definitions without looking for the DEFAULT_FASTRTPS_PROFILES.xml in the working directory. For more information about XML profiles, please refer to XML profiles.

Linux

 
export SKIP_DEFAULT_XML=1

Windows

 
set SKIP_DEFAULT_XML=1

12.3. ROS_DISCOVERY_SERVER

Warning

The environment variable is only used in the case where discovery protocol is set to SIMPLE, SERVER, or BACKUP. In any other case, the environment variable has no effect.

Setting this variable configures the DomainParticipant to connect to one or more servers using the Discovery Server discovery mechanism.

  • If ROS_DISCOVERY_SERVER is defined, and the DomainParticipant’s discovery protocol, is set to SIMPLE, then Fast DDS will instead configure it as CLIENT of the given server.

  • If ROS_DISCOVERY_SERVER is defined, and the DomainParticipant’s discovery protocol is SERVER or BACKUP, then the variable is used to add remote servers to the given server, leaving the discovery protocol as SERVER or BACKUP respectively.

  • The value of the variable must list the locator of the server in the form of:

    • An IPv4 address like 192.168.2.23. The UDP port can be appended using : as in 192.168.2.23:35665.

    • An IPv6 address that follows RFC3513 address convention like 1080::8:800:200C:417A. Again a UDP port can be appended like in [1080::8:800:200C:417A]:35665. Note the use of square brackets to avoid ambiguities.

    • A DNS name can be specified. This name will be used to query known hosts and available DNS servers to try to resolve valid IP addresses. Several formats are acceptable:

      • Plain domain name: eprosima.com. This will include all available IP addresses.

      • Domain name + port: eprosima.com:35665. As above but using a specific port.

      • UDPv4 specifier + domain name: UDPv4:[eprosima.com]. Only the first IPv4 address resolved will be used.

      • UDPv4 specifier + domain name + port: UDPv4:[eprosima.com]:35665. As above but using a specific port.

      • UDPv6 specifier + domain name: UDPv6:[eprosima.com]. Only the first IPv6 address resolved will be used.

      • UDPv6 specifier + domain name + port: UDPv6:[eprosima.com]:35665. As above but using a specific port.

  • If no port is specified, the default port 11811 is used.

  • To set more than one server’s address, they must be separated by semicolons.

  • The server’s ID is determined by their position in the list. Two semicolons together means the corresponding ID is free.

The following example shows how to set the address of two remote discovery servers with addresses ‘84.22.259.329:8888’ and ‘localhost:1234’ and IDs 0 and 2 respectively.

Linux

 
export ROS_DISCOVERY_SERVER="84.22.259.329:8888;;localhost:1234"

Windows

 
set ROS_DISCOVERY_SERVER=84.22.259.329:8888;;localhost:1234

Important

IP addresses specified in ROS_DISCOVERY_SERVER must be either valid IPv4/IPv6 addresses or domain names. If a name can be resolved into several addresses it is possible to either use them all or restrict the selection to the first IPv4 or IPv6 address using the UDPv4: and UDPv6: prefixes respectively.

Important

This environment variable is meant to be used in combination with Fast DDS discovery CLI. The server’s ID is used by Fast DDS to derived the GuidPrefix_t of the server. If the server is not instantiated using the CLI, the server’s GUID prefix should adhere to the same schema as the one generated from the CLI. Else, the clients configured with this environment variable will not be able to establish a connection with the server, thus not being able to connect to other clients either. The server’s GUID prefixes generated by the CLI comply with the following schema: 44.53.<server-id-in-hex>.5f.45.50.52.4f.53.49.4d.41. This prefix schema has been chosen for its ASCII translation: DS<id_in_hex>_EPROSIMA.

Important

This environment variable can be changed at runtime adding new remote servers to a SERVER, BACKUP or CLIENT (that has been initialized with this environment variable previously) if loaded from an environment file using FASTDDS_ENVIRONMENT_FILE.

12.4. FASTDDS_STATISTICS

Warning

The environment variable is only used in the case where the CMake option FASTDDS_STATISTICS has been enabled. In any other case, the environment variable has no effect. Please, refer to CMake options for more information.

Setting this variable configures the DomainParticipant to enable the statistics DataWriters which topics are contained in the list set in this environment variable. The elements of the list should be separated by semicolons and match the statistics topic name aliases.

For example, to enable the statistics DataWriters that report the latency measurements, the environment variable should be set as follows:

Linux

 
export FASTDDS_STATISTICS="HISTORY_LATENCY_TOPIC;NETWORK_LATENCY_TOPIC"

Windows

 
set FASTDDS_STATISTICS=HISTORY_LATENCY_TOPIC;NETWORK_LATENCY_TOPIC

Important

This environment variable can be used together with the XML profiles (for more information please refer to Automatically enabling statistics DataWriters). The statistics DataWriters that will be enabled is the union between the ones specified in the XML file (if loaded) and the ones stated in the environment variable (if set).

12.5. FASTDDS_ENVIRONMENT_FILE

Setting this environment variable to an existing json file allows to load the environment variables from the file instead of from the environment. This allows to change the value of some environment variables at run time with just modifying and saving the changes to the file. The environment value can be either an absolute or relative path. The file format is as follows:

{
    "environment_variable_name_1": "environment_variable_value_1",
    "environment_variable_name_2": "environment_variable_value_2"
}

Important

The environment variables set in the environment file have precedence over the environment.

Warning

Currently only ROS_DISCOVERY_SERVER environment variable allows for changes at run time. (see Modifying remote servers list at run time)